I have an apple tree, a peach tree, and some grape vines. They’re not big trees, but they give too much fruit to eat. The squirrels get some, and we give some away. As for the rest, I began making wine and apple jack a few years back, but there’s still more fruit than I can use. Being a chemical engineer, I decided to make brandy this year, so far only with pears and apples.

The first steps were the simplest: I collected fruit in a 5 gallon, Ace bucket, and mashed it using a 2×4. I then added some sugar and water and some yeast and let it sit with a cover for a week or two. Bread yeast worked fine for this, and gives a warm flavor, IMHO. A week or so later, I put the mush into a press I had fro grapes, shown below, and extracted the fermented juice. I used a cheesecloth bag with one squeezing, no bag with the other. The bag helped, making cleanup easier.

I did a second fermentation with both batches of fermented mash. This was done in a pot over a hot-plate on warm. I added more sugar and some more yeast and let it ferment for a few more days at about 78°F. To avoid bad yeasts, I washed out the pot and the ace bucket with dilute iodine before using them– I have lots of dilute iodine around from the COVID years. The product went into the aluminum “corn-cooker” shown above, 5 or 6 gallon size, that serves as the still boiler. The aluminum cover of the pot was drilled with a 1″ hole; I then screwed in a 10″ length of 3/4″ galvanized pipe, added a reducing elbow, and screwed that into a flat-plate heat exchanger, shown below. The heat exchanger serves as the condenser, while the 3/4″ pipe is like the cap on a moonshiner still. Its purpose is to keep the foam and splatter from getting in the condenser.

I put the pot on the propane burner stand shown, sealed the lid with masking tape (it worked better than duct tape), hooked up the heat exchanger to a water flow, and started cooking. If you don’t feel like making a still this way, you can buy one at Home Depot for about $150. Whatever route you go, get a good heat exchanger/ condenser. The one on the Home-depot still looks awful. You need to be able to take heat out as fast as the fire puts heat in, and you’ll need minimal pressure drop or the lid won’t seal. The Home Depot still has too little area and too much back-pressure, IMHO. Also, get a good thermometer and put it in the head-space of the pot. I used a thermocouple. Temperature is the only reasonable way to keep track of the progress and avoid toxic distillate.

The extra weight of the heat exchanger and pipe helps hold the lid down, by the way, but it would not be enough if there was a lot of back pressure in the heat exchanger-condenser. If your lid doesn’t seal, you’ll lose your product. If you have problems, get a better heat exchanger. I made sure that the distillate flows down as it condenses. Up-flow adds back pressure and reduces condenser efficiency. I cooled the condenser with water circulated to a bucket with the cooling water flowing up, counter current to the distillate flow. I could have used tap water via a hose with proper fittings for cooling, but was afraid of major leaks all over the floor.

With the system shown, and the propane on high, it took about 20 minutes to raise the temperature to near boiling. To avoid splatter, I turned down the heater as the temperature approached 150°F. The first distillate came out at 165°F, a temperature that indicated it was not alcohol or anything you’d want to drink. I threw away the first 2-3 oz of this product. You can sniff or sip a tiny amount to convince yourself that this this is really nasty, acetone, I suspect, plus ethyl acetate, and maybe some ether and methanol. Throw it away!

After the first 2-3 ounces, I collected everything to 211°F. Product started coming in earnest at about 172°F. I ended distillation at 211°F when I’d collected nearly 3 quarts. For my first run, my electronic thermometer was off and I stopped too early — you need a good thermometer. The material I collected and was OK in taste, especially when diluted a bit. To test the strength, I set some on fire, the classic “100% proof test”, and diluted till it to about 70% beyond. This is 70% proof, by the classic method. I also tried a refractometer, comparing the results to whiskey. I was aiming for 60-80 proof (30-40%).

I tried distilling a second time to improve the flavor. The result was stronger, but much worse tasting with a loss of fruit flavor. By contrast, a much better resulted from putting some distillate (one pass) in an oak barrel we had used for wine. Just one day in the barrel helped a lot. I’ve also seen success putting charred wood cubes set into a glass bottle of distillate. Note: my barrel, as purchased, had leaks. I sealed them with wood glue before use.

I only looked up distilling law after my runs. It varies state to state. In Michigan, making spirits for consumption, either 1 gal or 60,000 gal/year, requires a “Distilling, Rectifying, Blending and/or Bottling Spirits” Permit, from the ATF Tax and Trade Bureau (“TTB”) plus a Small Distiller license from Michigan. Based on the sale of stills at Home Depot and a call to the ATF, it appears there is little interest in pursuing home distillers who do not sell, despite the activity being illegal. This appears similar to state of affairs with personal use marijuana growers in the state. Your state’s laws may be different, and your revenuers may be more enthusiastic. If you decide to distill, here’s some music, the Dukes of Hazard theme song.

Robert Buxbaum, November 23, 2022.